Video: 5 Tips to Improve Your A/C's Performance

Leave a Comment - 5

Comments

Lowell Shatraw

Subject: Air Conditioners

What about SWAMP COOLERS, or Portable AC units. You need to cover ALL the bases and not leave the rest of us hanging.

Charles hvac tech.

Subject: A/C tip

A/C units are only designed to keep your home 20 deg below outdoor temp and are running at max capacity at 95 deg outdoor temp. Trying to keep 70 or below when it is in the 90's outside will result in high light bill and units running constantly durring peak hours and cause compressor overheating. Do not set your thermostats at lower temps in hotter temps.

John Smith

Subject: My AC stopped working during

My AC stopped working during the late evening hours somedays before. I opened the unit and found that thick ice had formed over the coils. Can you please suggest me what went wrong?

Lou

Subject: ice forming in an AC unit

Ice forms in an AC unit when you have the temps set low and the fan on a low speed as well.. To prevent it, always keep the fan on a higher speed. If you want less cooling and need to turn the fan down, then raise the temp setting.. when it's VERY cold, a slow running fan can't compensate for the temp good enough, condensation forms on the coils, then precedes to freeze, or "frost up" which turns into a block of ice on your coils.. Just turn it off for a while to let it melt, (never try and dig it out, all your going to do is end up damaging your coils and losing your freon, maybe destroying the unit), and when you turn it back on remember, if you want: low temps, use high speed fan settings, and if you lower the fan speed, then raise the temp setting.. It's easy to remember, if you just remember they are opposites. low fan speed for high temp, and high fan for low temps

View Comments - 5 Hide Comments

Post New Comment

 
Close
Offers <
Deals
Popular <
Answers <

Answers

?
what should you pay.  You pay what you can afford.  1100sqft unit requires a min. of a two ton unit.  prices range from 2100-2900 depending upon the seers of the system.  13 seer is the min. the law requires  and for your situation with 1100 sqft.  do not worry about the seers as long as it is to code.  the bigger the house the more seers for economy.  1100 sqft is at the border line for a two ton system.  It is more important to have your new system balance, there is where you get the economy on your electric bill and gas.  Bryant, lenox, ruud and carrier are the brands you should stay with.All have the same basic factory warrantee and will last you longer than you expect as long as you maintain it with regular check ups twice a year once in the spring and then in the fall.

raymond gonzalez
koolray heating and air
 clarksville,tn
?

APRStore.com offers a nice sizing chart for HVAC capacitors and furnace capacitors. Most of the capacitors I've looked at are $5 to $15 dollars, so a little less than Home Depot and Lowes.

 

Replacement is really easy, but be sure to watch a youtube video on how to replace it like this one: https://www.youtube.com/watch?v=_IpydZIsOJg

 

Stay safe and hire a professional if you feel unsure about doing it yourself!

?
The only thing of importance, is the hvac professional you choose to use. Alot of manufacturer's pieces are built relatively the same, and will last about the same amount of time. The thing that matters most is what you can not compare between companies, and that is the installation. Purchasing a system is not like purchasing a car, where no matter where you buy it, they are all the same. Each installation is different, and usually what you are paying for is the level of expertise, and quality of the installation, the company who will actual give you the warranty, and the comfort that you will receive. Manufacturers warranties disappear every day. They always have a loophole where they can get out of paying, but your local dealer wants to keep you happy for future work, and to protect his reputation in the communiy. Look up 4 year old Nordyne and Goodman warranty problems. Choose the HVAC professional first. It will cost you the least in the long run. I have had to totally redo plenty of installations that were just performed because of an uncomfortable customer, and a system that keeps breaking down. The equipment is only as good as it's installation, and over 70% are not installed correctly.
?
I think maybe you are confusing SEER, which is an efficiency-related rating (higher SEER means more effective use of the electric power used to compress the gas), and TONS rating, which is a measure of the total cooling power of the system. (Tons used to mean how many tons per hour of ice was used in evaporative cooling building systems - a Refrigeration or Cooling Ton equals 12,000 Btu/Hour of energy exchange. A BTU, which is another antique measure but still used, is the energy needed to change the temperature of a pound of water one degree fahrenheit. Unfortunately, because of varying humidity and evaporation, this is not readily related to house air heating or cooling without a lot of assumptions and some computations. Relating this to today's world - the Manuals BayAreaAc referred to account for all these energy conversions and determine an estimated cooling (or heating) requirement for your specific house. The type of construction, solar exposure, general climatic conditions such as average temperatures, humidity, and hottest and coldest normal ambient temperatures and desired inside temperture are all taken into account in the more sophisticated versions of the analysis, so there is no "standard", though a rough old rule of thumb was about 1 ton of cooling per 500SF of house. Obviously, this was a WAG only because it did not account for insulation, type of roofing, whether you live in Alaska or Miami, etc. The ACCA manuals do a very simplified form of evaluation to arrive at a "design", which generally will be adequate. OF course, highly precise calculations are not really needed because A/C units generally come in even ton ratings - so if you are at say 2.6 ton requirement you will be getting a 3-ton unit anyway. SEER ratings are not a direct measure of efficiency, but the relative difference between ratings gives you good idea of the unit's relative efficency in using electricity - so a 16 SEER should be about 19% more efficient (so roughly comparable lower electricity bill) than a comparably sized 13 SEER unit. 13 SEER is the lowest efficiency currently allowed to be built for general use, 19 SEER is about the highest efficiency made by pretty much all manufacturers, and about 25 SEER is the highest rated though very pricey shelf-item units, though special construction custom units can reach about 30 SEER. Note however, like any government sponsored rating, much of it is hooey when you get down to it - for instance, SEER ratings are figured based on 80 degree inside air temp and 82 degrees outside, when that is far from the normal case of mid to low seventies inside and high eighties or above outdoors. This makes the absolute SEER rating meaningless, but relative numbers still have meaning in comparing units. Note these efficiency ratings are for conventional air conditoners and heat pumps working in ambient air conditions. Ground sourced Geothermal or lake/river exchange cooling units, though initially more expensive in most cases, can greatly exceed the air-exchange unit efficiencies because they are exchanging heat with cold natural water rather than with a high-temperature outside air, and instead of continually compressing a gas are just circulating cold water. I worked on one geothermal cooling project which had almost infinite efficiency, which of course makes no sense - but the only power was for sensors and a control valve as the water flow was single-pass under gravity flow, so no power was used to circulate the water.