Wapakoneta HVAC Contractors

in Wapakoneta, OH

80
HVAC Contractors are
in Wapakoneta

35
HVAC Contractors in Wapakoneta
are top rated

A
Rated by
Stephen M.
"Everything was done when they said it would be done and for the price they quoted. I am really impressed with the knowledge. I thought it would be a nightmare and have a lot of problems." It was great. These guys know what they are doing. No problems at all. The system works great.
A
Rated by
MARK H.
"
arrived on time, quickly gave me an estimate, and he started work. He informed me that code required that the new wired lights required an arc fault breaker," and he tested and supplied the new breaker. He did the trouble-shooting for the service switch and told me he did not have the part on hand. I offered to make a run for it, and he moved on to the boiler circuit. By the time I returned with the correct switch for the service cutoff, he was just finishing up the surge suppressor installation. He completed all tasks, cleaned up his work areas and tested everything. Could not be more pleased.
A
Rated by
Valerie R.
"I was able to get an appointment for the day and time I wanted. The plumber arrived right on time. He was polite and friendly, and came prepared to complete the requested service" of installing a new garbage disposal. While at my home, I asked him to also look at my kitchen faucet because it was becoming "wobbly". He went to work immediately on the garbage disposal and then repaired my faucet to work like new. The plumber left the work area neat and clean when he was finished,. I was very pleased with all of the services, was impressed with how quickly and efficiently the work was completed, and will use them again for my next plumbing needs.

Local Articles in Wapakoneta

Winter guide

The Angie's List Guide to Winter Maintenance

It's the time of year when the winter weather can take a toll. Follow this winter maintenance checklist to protect your home, your car and your health.

An HVAC expert needs training in both electronics and plumbing. (Photo submitted by Angie's List member Dave M.)

Hiring an HVAC service

The awkward-to-pronounce acronym stands for "heating, ventilation and air conditioning" which in many respects are completely different processes.

If you are looking for the peak of heating and cooling efficiency and performance, a Frigidaire system can address your needs.
Heating & A/C

The efficiency of your new furnace is one of the most crucial aspects of long-term performance for your unit. Learn what's recommended for your region.

heat pump
Heating & A/C

Heat pumps have many advantages, but most homeowners aren't sure how much a heat pump costs to install and operate, compared to normal central air HVAC systems.

New furnaces also have more safety controls and sensors than older furnaces, says Unsdorfer. (Photo courtesy of Central Heating & Air Conditioning Co.)
Heating & A/C

Learn how to know when it's time to replace your furnace, and to determine what type will replace it. Expect to see higher efficiency and lower heating bills.

filter replacement
Air Duct Cleaning, Heating & A/C

Heating and air conditioning service professionals share tips to keep your HVAC system in great shape and protect yourself from scammers.

Angie's Answers

?

No one can tell you what another contractor will charge. There is no one set price for heating and air-conditioning equipment installation. One of the major factors that affect your price is its size. No one can tell you what size equipment you’ll need without doing a load analysis on the home. That calculation essentially determines the insulation value of the home, i.e... What is the heat gain of the home, what are some other prevailing factors like room equipment, solar gain, or natural shading? You can compare prices between contractors to gauge what your cost would be between contractors, but this is a little tricky to do. Let me explain a little more. Let's say you get an installation quote of $5050.00 from contractor “A” who employs three technicians and operates two trucks. He also runs his operation from home. Contractor “B” charges $6200.00 to do the same job but has 10 employees and 5 trucks. He works out of a rental unit and offers his people a little bit better of a benefit package to recruit highly motivated workers. Everything else being equal (equipment size, SEER rating, furnace efficiency, brand name and additional material—other things that affect the price), is either one of these contractors defrauding you? No, their overhead is different. All these things play into a company’s labor rate. Just be aware of your expectations when it comes to performing any kind work in your home. If you want to pay an extremely low-inexpensive price below the average installation cost in your area then you are highly likely to get the quality of work that comes with that cost. Remember cheaper is not better!

?
Yes Jupiter. It depends on the severity of the situation, is the mold encapsulated in the insulation. If yes, than replace [insulation] it with new. Is it on the casing of the heater? If yes, clean it with a mold neutralizing metal cleaner. It's not a matter of finding something or someone to clean or address the existing mold. It's a matter of finding a contractor to rectify what is causing the mold grow. It's coming from excessive moisture in the air-handler unit. I can say with 100% surety you’re dealing with poor airflow and/or incorrect equipment sizing! Either issue will cause excessive icing of the evaporator coil, which leads to excessive condensate water in the system. The condensate will eventually overflow the drain pan leaving stagnant water in the air-handler housing, which leads to mold growth. I would not let any contractor do any kind of temporary repair, add any device like a UV light or air-cleaning product until the aforementioned is corrected. I talk a lot about this in my videos and on my website. It is the result of improper system design from unqualified contractors. There is a reason why some guys cost more than others, and this is one reason why!




?

The furnaces are both good. They come with the same warranty. More importantly it is the installation process that is most important. Both of these furnaces need to be setup properly as they both tend to be particular if installed incorrectly.

I will say that I am a York Certified comfort Expert. I have in the past been a Trane Dealer. I used to dislike York, but since Johnson Controls bought them, they have improved drastically. Since Ingersollrand bought Trane they have improved slightly, but I am not impressed.

The differences in both are as follows (these are both top of the line form theier manufacturers):

The Trane has a 95% Efficiency The York is 98% efficient.

The Trane has 2 stages of heating the York has 100 stages of heating.

Both systems have variable speed motors with different modes, Trane has Comfort R and York has ClimaTrak, both pretty much the same.  Setup of the dipswitches/jumpers are the most importnant and vary by system size and your climate.

The Trane has an external trap and is either upflow or downflow. The York is 4 way compatible with an internal trap.

The Trane has a nicer furnace cabinet, but most of the time the furnace is hidden and is irelevant.

Some Trane units are made in Monterey, Mexico. All York units are Made in Witchita, Kansas or Norman , Oklahoma. (some interanl components are made overseas in both units, but all Yorks are assembled in USA).

Depending on your installation companies relationship, then the support they get from the manufacturer differs. I have found that if you buy alot of Trane you get good service, if you do not, then service is not that great. The same may be said about York, but so far I have great support from York. York will work with the smaller companies more than Trane will (my opinion).  Again, I have sold, installed and repaired from both manufacturers so I have knowledge in both. I also used to dislike York. If you are in the trade, I invite you to look at the new York line of systems. You will may be impressed.

 

I think both products offer the best furnaces available, compared to other brands.  Depending on who installs it is most important as well as their relationship with the manufacturers.  Both good products.  I hope that helps.

 

Justin

A NATE Certified Mechanical Contractor.

?
The only thing of importance, is the hvac professional you choose to use. Alot of manufacturer's pieces are built relatively the same, and will last about the same amount of time. The thing that matters most is what you can not compare between companies, and that is the installation. Purchasing a system is not like purchasing a car, where no matter where you buy it, they are all the same. Each installation is different, and usually what you are paying for is the level of expertise, and quality of the installation, the company who will actual give you the warranty, and the comfort that you will receive. Manufacturers warranties disappear every day. They always have a loophole where they can get out of paying, but your local dealer wants to keep you happy for future work, and to protect his reputation in the communiy. Look up 4 year old Nordyne and Goodman warranty problems. Choose the HVAC professional first. It will cost you the least in the long run. I have had to totally redo plenty of installations that were just performed because of an uncomfortable customer, and a system that keeps breaking down. The equipment is only as good as it's installation, and over 70% are not installed correctly.
?
I think maybe you are confusing SEER, which is an efficiency-related rating (higher SEER means more effective use of the electric power used to compress the gas), and TONS rating, which is a measure of the total cooling power of the system. (Tons used to mean how many tons per hour of ice was used in evaporative cooling building systems - a Refrigeration or Cooling Ton equals 12,000 Btu/Hour of energy exchange. A BTU, which is another antique measure but still used, is the energy needed to change the temperature of a pound of water one degree fahrenheit. Unfortunately, because of varying humidity and evaporation, this is not readily related to house air heating or cooling without a lot of assumptions and some computations. Relating this to today's world - the Manuals BayAreaAc referred to account for all these energy conversions and determine an estimated cooling (or heating) requirement for your specific house. The type of construction, solar exposure, general climatic conditions such as average temperatures, humidity, and hottest and coldest normal ambient temperatures and desired inside temperture are all taken into account in the more sophisticated versions of the analysis, so there is no "standard", though a rough old rule of thumb was about 1 ton of cooling per 500SF of house. Obviously, this was a WAG only because it did not account for insulation, type of roofing, whether you live in Alaska or Miami, etc. The ACCA manuals do a very simplified form of evaluation to arrive at a "design", which generally will be adequate. OF course, highly precise calculations are not really needed because A/C units generally come in even ton ratings - so if you are at say 2.6 ton requirement you will be getting a 3-ton unit anyway. SEER ratings are not a direct measure of efficiency, but the relative difference between ratings gives you good idea of the unit's relative efficency in using electricity - so a 16 SEER should be about 19% more efficient (so roughly comparable lower electricity bill) than a comparably sized 13 SEER unit. 13 SEER is the lowest efficiency currently allowed to be built for general use, 19 SEER is about the highest efficiency made by pretty much all manufacturers, and about 25 SEER is the highest rated though very pricey shelf-item units, though special construction custom units can reach about 30 SEER. Note however, like any government sponsored rating, much of it is hooey when you get down to it - for instance, SEER ratings are figured based on 80 degree inside air temp and 82 degrees outside, when that is far from the normal case of mid to low seventies inside and high eighties or above outdoors. This makes the absolute SEER rating meaningless, but relative numbers still have meaning in comparing units. Note these efficiency ratings are for conventional air conditoners and heat pumps working in ambient air conditions. Ground sourced Geothermal or lake/river exchange cooling units, though initially more expensive in most cases, can greatly exceed the air-exchange unit efficiencies because they are exchanging heat with cold natural water rather than with a high-temperature outside air, and instead of continually compressing a gas are just circulating cold water. I worked on one geothermal cooling project which had almost infinite efficiency, which of course makes no sense - but the only power was for sensors and a control valve as the water flow was single-pass under gravity flow, so no power was used to circulate the water.
?
YOU.
You bought the home after an inspection that told you there were issues?
Every state has different laws regarding home purchases, contact your real estate agent to find out what remedies may apply.
THIS IS EXACTLY why you hire QUALIFIED and LICENSED contractors.

Doug
AirTekHP
CSLB# 824188 

Hvac reviews in Wapakoneta

A

Rating
Wapakoneta HVAC Contractors Provider Name Locked
and
Wapakoneta HVAC Contractors Provider Name Locked
. replaced our furnace on December 2, 2012, after our old furnace died the night before. We were evacuated on December 1st due to extremely high levels of carbon monoxide coming from our old furnace. I was hospitalized. A family member called
Wapakoneta HVAC Contractors Provider Name Locked
Walker's company and they were already working on taking out the old furnace when I came home from the hospital on the morning of December 2nd. They installed a new furnace, a/c and some new duct work and had it working that day! We were able to return home and continue decorating for Christmas! (We did have a carbon monoxide alarm it didn't work...we quickly replaced it, as well.) I was not a member of Angie's List when all of this occurred or I would have shared this earlier.
This past summer, my air conditioner suddenly stopped cooling. I called
Wapakoneta HVAC Contractors Provider Name Locked
and
Wapakoneta HVAC Contractors Provider Name Locked
. to find out what kind of service plan we had with them. We didn't have a plan and I was concerned it would take a while to have them come out since it was a busy time of year and a hot day. I told them that I have MS and have tremendous difficulty in hot temperatures. Someone came out to my home within a couple of hours. They quickly fixed the problem and said there would be no charge.
As soon as I became a member of Angie's List, I checked to see if
Wapakoneta HVAC Contractors Provider Name Locked
and
Wapakoneta HVAC Contractors Provider Name Locked
was listed. I was so pleased to see them here (but not at all surprised)! I have spoken to
Wapakoneta HVAC Contractors Provider Name Locked
(the owner) and several of him employees several times. They are always kind, professional and prompt. I highly recommend this company, as I have always found their customer service and work to be excellent!
- Rachel B.
A

Rating
It was a Big Deal purchase. They did a very good job. I was pleased with their service. There was no extra charge. There was only one individual. He was honest and truthful regarding our A/C unit. He recommended some services but was honest in stating that it would not probably change our cost and it probably would not be a good return on investment although that would be the next step that would be required and he suggested that we maintain what we have because this is more cost-effective to us at this time. We were very appreciative that he relayed to us what was actual and what was required as a suggestion. He was just very, very pleasant and personable. I would absolutely use them again.
- Christine D.
A

Rating
I wasn't home but my husband said they did a terrific job. They were only scheduled to do the duct cleaning but he ended up adding on the gas fireplaces which he was super glad he did. He couldn't say enough good things about them. They even sent him some pictures of the work they completed which I thought was a really great idea!
- Tara A.
A

Rating
Job was well-planned and completed. The pump has functioned flawlessly. Very professional and on time. Price quote was exactly the same as the final charge.
- Paul B.
A

Rating
I called first thing in the morning and was able to get a technician at my house about 40 minutes later (15 minutes faster than promised!) He was polite, knowledgable, efficient, and very transparent about pricing. We will call
Wapakoneta HVAC Contractors Provider Name Locked
again in the future with any heating problems we encounter.
- Julia G.
F

Rating
He did NOTHING!


Update on 10/19/2014 from Provider Response:

Well if was only for an inspection then I would have never purchase this deal from Angie's List. This is false advertising then. Deal said TUNE-UP and REPLACE FILTER, which he also did not do. There was a bunch of things he was suppose to do on a TO DO LIST which he did not perform also.
- JIMMY C.
A

Rating
The tech quickly discovered that the capacitor was blown in addition to the broken fan blade. Because of the age of the unit, the tech stated that he would need to locate a fan blade unit. He left to locate the blade and returned in a little over an hour with a fan blade and capacitor, swiftly made the replaces and had the central AC unit back in business.
- Germaine M.

All HVAC Contractors in Wapakoneta, OH

Companies below are listed in alphabetical order. To view top rated service providers along with reviews and ratings, Join Angie's List Now!

4 Star Plumbing Heating & A/C

08049 US Hwy 127
Bryan

A&A Mechanical LLC

717 E Crawford St
Van Wert

AFFORDABLE HEATING & COOLING

949 EAST MAIN STREET
Chillicothe

Air Excellence Heating & Cooling Inc

525 N 5th St
Steubenville

All Temp Refridgeration Inc

18996 State Rt 66 N
Delphos

American Home Shield

889 Ridge Lake Blvd

AppliancePartsPros.com

16501 Ventura Blvd Ste 500

AREA ENERGY & ELECTRIC INC

2001 COMMERCE DR
Sidney

Ayers Mechanical Group LLC

222 N Market St
Van Wert

B Cook & Son Plumbing & Heating

11 E Mechanic St
Wapakoneta

Bill Ahrens Plbg & Htg

8751 Burns Rd
Versailles

Blue Ridge Builders

604 Schaum Ave.
Zanesville

Buschur's Refrigeration

541 N Eastern Ave
Saint Henry

Chilltex LLC

7517 Hoying Rd
Anna

Cowboys Heating and Air

10801 Hemple Rd
Farmersville

Danco Enterprises Inc

6220 Knollwood Rd
Springfield

Doctor Flue Inc

1610 Dinius Rd

Easton Water Solutions LLC

1040 South Main St
Bellefontaine

Edwards Heating And Cooling

1164 Homer St
Logan

Eisert Plumbing & Heating

1103 Apollo Dr
Wapakoneta

FALLER MECHANICAL LLC

2091 SAINT JOE RD
Fort Recovery

Furnace Guys

5344 Center St
Hilliard

Gasser Builders Inc

2215 Eastern Rd
Rittman

Geiler Home Services

6561 Glenway Ave
Cincinnati

Hey Neighbor LLC

320 Main St
Ravenna

Holmes Improvements

3905 E State Rd
Elida

House Master Home Inspections

1734 Forest Hills Cir
Zanesville

Huebner

1155 Canton Rd NW
Carrollton

John P Timmerman Co - Lima

4563 Elida Rd
Elida

Keim Lumber Co

4465 St Rte 557
Charm

KINN BROTHERS HEATING AIR COND

527 WHETSTONE ST
Bucyrus

Knueve & Sons Inc

102 E Water St
Kalida

KOGGE PLUMBING, HEATING & A/C, INC.

811 Indiana Ave
Saint Marys

Kozik Plumbing Heating & Cooling

421 S Riblet St
Galion

Liberty Air Technicians Ltd.

11276 County RD 1
Chesapeake

Lochard Inc Sheet Metal

903 Wapakoneta Ave
Sidney

MATT'S HEATING & COOLING

1000 S Defiance Trail
Spencerville

Monfort Heating & Air Conditioning

2319 Armstrong Dr
Sidney

MONROE HEATING & AIR

P.O. Box 344
Toronto

Moran Bros

460 Township Road 130
Harrod

Morans Refrigeration

820 S Wayne St
Saint Marys

Orrison Maintenance Inc

67560 Morristown Flushing Rd
Belmont

Premier Mechanical Service

912 S Metcalf St
Lima

Quality Electrical Services

1190 E Kibby St
Lima

Quality Mechanical Co.

8140 Wildwood Ln
Athens

Quality Mechanical Services

1190 E Kibby St
Lima

QUALITY PLUMBING HEATING & AC

701 NORTH ST
Wapakoneta

Reliant Mechanical Inc.

3271 County Road 154
East Liberty

Renewable Engineered Systems

22 East Church Street

RepairClinic.com Inc

48600 Michigan Ave

RICHARD LEWIS

14867 STATE ROUTE 125
West Union

Riesen Plumbing & Heating

2015 SR 703
Celina

Ron's Heating & Cooling

202 Logan St
Dennison

SCHNIPPEL ELECTRIC PLUMBING

12848 HARDIN PIKE
Wapakoneta

Sebastian Construction

16514 Highway 10 N

Service Tech Plumbing & Heating inc.

2050 S Conant Rd
Spencerville

Shearer's Plumbing & Electrical

106 N Main St
Mount Blanchard

Total Service Center

00020 US Route 33
Saint Marys

Warmzone

12637 S 265 W Suite 100

Washam Plumbing Heating & Ac

5028 Poling Rd
Lima

Wellman Services

333 N Jackson St
Lima

WORLDWIDE FILTERS LLC

3318 Pagosa Ct
Wapakoneta Zip Codes

Join Angie's List to get the best local reviews in Wapakoneta.

What Does My Membership Include?
  • Instant access to reviews for 700+ services
  • Exclusive service discounts - up to 70 percent off!
  • Top-notch support from our live call center
How does Angie's List work?
1. Say you need a Heating Repair
2. Angie's List has tons of detailed, local reviews.
3. Find a winner, and book them.
4. Angie's List is there to resolve any issues.
CBS
Good Morning America
Fox News
USA Today
The Wall Street Journal
MSN money