-Find top-rated Service Providers

Find Top-Rated Clinton HVAC Contractors

Angie's List helps you hire the best - and avoid the rest!

HVAC Contractors to Avoid


Top Rated HVAC Contractors


Prevent buyer's remorse with us

  • Over 3 million people trust Angie's List to help make the right choice
  • Be informed to avoid costly mistakes
  • Shop with us to ensure a fair price
  • Our complaint resolution team will help if a project goes bad
+See Verified Local Reviews

Over 3,613 reviews for
Clinton HVAC Contractors from people just like you.

"I cannot even express how professional this company is my story is a long one but all I can say is I will continue to use this company as long as I can and I hope"
will always be my technician..
is the sweetest person you could ever speak to and she listens and does not put you off....
found out I needed a new motor our insurance company could not work with their Company so I had to call American home Shield to find someone else.they sent out a company called Infinityheating and air all I have to say to anybody who reads this is beware this company infinity heating and air is a joke!!!when
came out again to check something they said was wrong there was actually nothing wrong the guy had turned off my heat for no reason it was just the motor..I am still waiting on a motor from Infinity heating and air!!and just to show you how professional
was he said he would come out and check the job that infinity heating and air did with the motor to make sure they did it properly...all I can say is thank you
thank you for all of your hard work on my roof and I will continue to use this wonderful professional company again and again..

-Joni A.

"I scheduled a furnace inspection with a deal through
for $60. The service rep found that the exhaust pipe was cracked and tried to charge" me $250 for a "diagnostic" without telling me what he was doing was going to be cost more than the $60 for the inspection. In the end, I ended up using the $60 coupon from Angie's list plus paying about $775 to replace the exhaust pipe. I think this charge was very high, so in the future, if anything major needs to be done, I will definitely shop around for a better price. I'm also concerned that 3 months later, the furnace is starting to do what it was doing previously (cycle on/off a few times when starting until it stays on) before the exhaust pipe was replaced.

-Matthew W.

+Join 2 Million People on Angie's List

Over 2 million people trust Angie's List.

  • Your Membership Includes:
  • Instant access to top rated businesses covering 700+ services
  • Our Complaint Resolution Team to help when a project goes bad
  • On-the-go access to our iPhone, Android, & iPad apps
Find top-rated Service Providers
See Verified Local Reviews
Join 2 Million People on Angie's List

Local Articles in Clinton

Hiring an HVAC service

The awkward-to-pronounce acronym stands for "heating, ventilation and air conditioning" which in many respects are completely different processes.


HVAC Maintenance

You can help your heating and cooling systems work more efficiently and last longer by tending to regular maintenance. Some things, like changing the furnace filter, can easily be done by the homeowner.

Because a ceiling fan doesn’t actually cool a room, you can turn off the fan when you leave the room and save on your electric bill. (Photo courtesy of Angie's List member Marvin Y. of Albany, New York)
Heating & A/C

Learning the real story behind some of those common air conditioning assumptions can help you to keep your system operating more efficiently.

 (Photo by Photo by Brandon Smith)
Heating & A/C

Learn more about the different efficiency ratings for HVAC equipment and how they impact the performance of your air conditioner, heat pump or furnace.

Heating & A/C

Three highly rated professionals explain how to best perform regular HVAC system maintenance.

You could be eligible for a federal tax credit if you installed a solar energy system in the past year. (Photo courtesy of Angie's List member Clint T. of Phoenix)
Heating & A/C

If you’ve had energy-efficient HVAC equipment installed, you could be eligible for federal or state incentives

Angie's Answers


No one can tell you what another contractor will charge. There is no one set price for heating and air-conditioning equipment installation. One of the major factors that affect your price is its size. No one can tell you what size equipment you’ll need without doing a load analysis on the home. That calculation essentially determines the insulation value of the home, i.e... What is the heat gain of the home, what are some other prevailing factors like room equipment, solar gain, or natural shading? You can compare prices between contractors to gauge what your cost would be between contractors, but this is a little tricky to do. Let me explain a little more. Let's say you get an installation quote of $5050.00 from contractor “A” who employs three technicians and operates two trucks. He also runs his operation from home. Contractor “B” charges $6200.00 to do the same job but has 10 employees and 5 trucks. He works out of a rental unit and offers his people a little bit better of a benefit package to recruit highly motivated workers. Everything else being equal (equipment size, SEER rating, furnace efficiency, brand name and additional material—other things that affect the price), is either one of these contractors defrauding you? No, their overhead is different. All these things play into a company’s labor rate. Just be aware of your expectations when it comes to performing any kind work in your home. If you want to pay an extremely low-inexpensive price below the average installation cost in your area then you are highly likely to get the quality of work that comes with that cost. Remember cheaper is not better!

The only thing of importance, is the hvac professional you choose to use. Alot of manufacturer's pieces are built relatively the same, and will last about the same amount of time. The thing that matters most is what you can not compare between companies, and that is the installation. Purchasing a system is not like purchasing a car, where no matter where you buy it, they are all the same. Each installation is different, and usually what you are paying for is the level of expertise, and quality of the installation, the company who will actual give you the warranty, and the comfort that you will receive. Manufacturers warranties disappear every day. They always have a loophole where they can get out of paying, but your local dealer wants to keep you happy for future work, and to protect his reputation in the communiy. Look up 4 year old Nordyne and Goodman warranty problems. Choose the HVAC professional first. It will cost you the least in the long run. I have had to totally redo plenty of installations that were just performed because of an uncomfortable customer, and a system that keeps breaking down. The equipment is only as good as it's installation, and over 70% are not installed correctly.
Yes Jupiter. It depends on the severity of the situation, is the mold encapsulated in the insulation. If yes, than replace [insulation] it with new. Is it on the casing of the heater? If yes, clean it with a mold neutralizing metal cleaner. It's not a matter of finding something or someone to clean or address the existing mold. It's a matter of finding a contractor to rectify what is causing the mold grow. It's coming from excessive moisture in the air-handler unit. I can say with 100% surety you’re dealing with poor airflow and/or incorrect equipment sizing! Either issue will cause excessive icing of the evaporator coil, which leads to excessive condensate water in the system. The condensate will eventually overflow the drain pan leaving stagnant water in the air-handler housing, which leads to mold growth. I would not let any contractor do any kind of temporary repair, add any device like a UV light or air-cleaning product until the aforementioned is corrected. I talk a lot about this in my videos and on my website. It is the result of improper system design from unqualified contractors. There is a reason why some guys cost more than others, and this is one reason why!

I'd rate them equal,or close,as with several other brands. I'd be more concerned about the difference in installation and service down the road. Difficult to determine the difference ,but asking for detailed info about their installation,may convince you to choose one over the other.

The Dept. of Energy states that poor installations can cause a 30% efficiency loss! Plus with Gas their are saftey issues,venting properly etc.,and of couse the need for a "low Level" Carbon Monoxide Alarm.
I think maybe you are confusing SEER, which is an efficiency-related rating (higher SEER means more effective use of the electric power used to compress the gas), and TONS rating, which is a measure of the total cooling power of the system. (Tons used to mean how many tons per hour of ice was used in evaporative cooling building systems - a Refrigeration or Cooling Ton equals 12,000 Btu/Hour of energy exchange. A BTU, which is another antique measure but still used, is the energy needed to change the temperature of a pound of water one degree fahrenheit. Unfortunately, because of varying humidity and evaporation, this is not readily related to house air heating or cooling without a lot of assumptions and some computations. Relating this to today's world - the Manuals BayAreaAc referred to account for all these energy conversions and determine an estimated cooling (or heating) requirement for your specific house. The type of construction, solar exposure, general climatic conditions such as average temperatures, humidity, and hottest and coldest normal ambient temperatures and desired inside temperture are all taken into account in the more sophisticated versions of the analysis, so there is no "standard", though a rough old rule of thumb was about 1 ton of cooling per 500SF of house. Obviously, this was a WAG only because it did not account for insulation, type of roofing, whether you live in Alaska or Miami, etc. The ACCA manuals do a very simplified form of evaluation to arrive at a "design", which generally will be adequate. OF course, highly precise calculations are not really needed because A/C units generally come in even ton ratings - so if you are at say 2.6 ton requirement you will be getting a 3-ton unit anyway. SEER ratings are not a direct measure of efficiency, but the relative difference between ratings gives you good idea of the unit's relative efficency in using electricity - so a 16 SEER should be about 19% more efficient (so roughly comparable lower electricity bill) than a comparably sized 13 SEER unit. 13 SEER is the lowest efficiency currently allowed to be built for general use, 19 SEER is about the highest efficiency made by pretty much all manufacturers, and about 25 SEER is the highest rated though very pricey shelf-item units, though special construction custom units can reach about 30 SEER. Note however, like any government sponsored rating, much of it is hooey when you get down to it - for instance, SEER ratings are figured based on 80 degree inside air temp and 82 degrees outside, when that is far from the normal case of mid to low seventies inside and high eighties or above outdoors. This makes the absolute SEER rating meaningless, but relative numbers still have meaning in comparing units. Note these efficiency ratings are for conventional air conditoners and heat pumps working in ambient air conditions. Ground sourced Geothermal or lake/river exchange cooling units, though initially more expensive in most cases, can greatly exceed the air-exchange unit efficiencies because they are exchanging heat with cold natural water rather than with a high-temperature outside air, and instead of continually compressing a gas are just circulating cold water. I worked on one geothermal cooling project which had almost infinite efficiency, which of course makes no sense - but the only power was for sensors and a control valve as the water flow was single-pass under gravity flow, so no power was used to circulate the water.
You bought the home after an inspection that told you there were issues?
Every state has different laws regarding home purchases, contact your real estate agent to find out what remedies may apply.
THIS IS EXACTLY why you hire QUALIFIED and LICENSED contractors.

CSLB# 824188 

Hvac reviews in Clinton


The contractor installed the return box in what appeared to be a good installation. However, a day or two later I peered into the return (by removing the air filter grill from the wall in the hallway) and could see into the return box. It was then I noticed that the contractor had cut a square opening out of the box to align this opening to another duct, which was fine; that needed to be done. But in doing that cutting and connecting, he did not seal the exposed fiberglass material, which like loose hairs, now flap freely as the air passes by and moves through the system. There is a reason that fiberboard has a baked on sealant, to keep the particles from releasing.
When I brought the above to his attention (a few days after the install), he said he would have someone come by and apply a sealant. It took a few calls and catching him on the phone to get him to commit to the latter, but several days passed by with nobody showing up to finish the job. I called him again and said I would do it myself it he could tell me what kind of sealant (mastic) to use, as I had done some research but wasn't positive how to go about doing this, or even if I should. He said he would drop off a pail of the material, which he did.
This is not a bad company, per
Clinton HVAC Contractors Provider Name Locked
, but it is not a good one. I had specific concerns, communicated them, and was willing to pay for work to waylay my concerns, yet the above is what I experienced. I am now contemplating having the entire box replaced with the type I originally wanted, which will cost me around $500. I could try to do the sealant application myself, but to do so would require that I purchase a special ladder (~$200 or more) to get into the return space in my wall and extend it high enough (attic height) to do the work.
If you know enough about HVAC work and have the time to watch everything this contractor does, then perhaps they might be ideal for you; but if you are an average homeowner who wants to hire a professional you can trust, this is not the contractor. I struggled to give them a C, but when I thought about the fact that they ignored my concern, a health hazard, they are lucky to get a D.
- matthew C.

mShowed up on time, did the work in a timely manner, explained the problem with the sensor and the impact an improperly installed sensor would have, then reworked its placement properly, suggesting that the way it was installed would eventually compromise the A/C compressor. He suggested we check the A/C system and found it to require additional freon, probably due to the improperly placed sensor, all in a timely manner.
Clinton HVAC Contractors Provider Name Locked
was the tech and he was efficient, timely, smart and took the time to explain the problem.
Clinton HVAC Contractors Provider Name Locked
is my new A/C-Heating R and R company. Thank you
Clinton HVAC Contractors Provider Name Locked
- jordan W.

We called
Clinton HVAC Contractors Provider Name Locked
Clinton HVAC Contractors Provider Name Locked
on a Sunday,
Clinton HVAC Contractors Provider Name Locked
came to our house right away, and started to fix the problem, it was the coldest day of the winter, we were very worried,
Clinton HVAC Contractors Provider Name Locked
has tried very hard to repair the heater, getting the replaced parts, he is very friendly and professional, he is very good at what he does, he has identified the problem right away, after getting all the needed part, he has fixed the problem and explained to us clearly what was wrong with our heater. I am very impressed by
Clinton HVAC Contractors Provider Name Locked
Clinton HVAC Contractors Provider Name Locked
, they are good people.
- qing H.

The work went far better than it would have with a technician less capable. All work was done according to schedule, in a timely manner, and
Clinton HVAC Contractors Provider Name Locked
was always very professional. He was willing to spend at least 2 hours without charge to explain to me the nature and extent of the problem, what would be needed to fix it, and how it would be fixed. This winter I had an unrelated problem in one of the units and called
Clinton HVAC Contractors Provider Name Locked
to check it out. I found out THEY WERE NO LONGER PROVIDING RESIDENTIAL SERVICES and received a referral to another provider..
- Joanne S.

The work
Clinton HVAC Contractors Provider Name Locked
did on the air conditioner took care of the problem and it's worked fine ever since. For the heating issue, I may not be able to tell if the steps
Clinton HVAC Contractors Provider Name Locked
gave me will work, but I think they will. He described exactly what he thought was happening and described other incidents that matched my problem. I appreciated the time he took to listen and try to diagnose what was going on.
- Susan S.

Tried to have my usual service install the thermostat without success. Looked up a installer on
Clinton HVAC Contractors Provider Name Locked
website and picked from top rated Angie's List company.
Clinton HVAC Contractors Provider Name Locked
was on time, looked at my system and had everything running in 30 minutes.
- Donald G.

Clinton HVAC Contractors Provider Name Locked
showed up when he said he would and performed the job nearly and quickly. I can tell that he takes the time to
Clinton HVAC Contractors Provider Name Locked
out a job so that it works well AND looks good. The price he quoted is the price we paid, and I felt good about it. Definitley high-quality workmanship. With plumbers, I strongly believe that you get what you pay for.
- Geri C.

My first interaction with
Clinton HVAC Contractors Provider Name Locked
was when my furnace went out on a Saturday morning after Christmas. The group that reqularly serviced
Clinton HVAC Contractors Provider Name Locked
could NOT be found. I called emergency numbers, went to the facility. I found
Clinton HVAC Contractors Provider Name Locked
in the phone book and
Clinton HVAC Contractors Provider Name Locked
came right out.
Of course we called them when we replaced
Clinton HVAC Contractors Provider Name Locked
. He came out and spent alot of time with me and my dad answering questions. I have had no problems with the funrace or service since. This was one of the best moves I made.
- Judith M.

All HVAC Contractors in Clinton, IA

Companies below are listed in alphabetical order. To view top rated service providers along with reviews and ratings, Join Angie's List Now!


16501 Ventura Blvd Ste 500


2205 E 53RD ST

Chambers Services Inc

1102 1/2 W MacArthur Ave

Clarinda Heating and Cooling

720 S 12th St

Collision Repair Center

1200 Avenue of the Cities

Complete Air-Care

519 N 3rd St
Red Oak

Converse Conditioned Air

3116 S Duff Ave Ste 100

Crawford Co

1306 Mill St

Cunningham Inc

808 South Market

Dan's Heating & Cooling

20751 475th St

DOTec Engineering Corp

424 Jefferson St

Ducts In A Row

939 Main St


1013 10TH AVE N


932 44TH AVE N


2799 Eagle Lake Drive

Kenco Construction LLC

16303 Bluegrass RD

Lane Plumbing & Heating Inc

2768 180th St
Mount Union

Midwest Climate Solutions

18918 109 Ave

Modern Mechanical

675 NE 45th Pl
Des Moines

Northwest Mechanical Inc

5885 Tremont Ave

Oldson's Plumbing Heating

114 N Commercial Ave
Eagle Grove

Premier Exteriors

4780 South 131 St.

Ragan Mechanical Inc.

702 W 76th Street

Service Guard a Division of Black Hills Energy

644 1st Street Suite #1
Webster City


1420 2ND AVE S


208 10TH ST NW
Mason City

The Schebler Co

5665 Fenno Rd

TMI - Total Maintenance Inc

1017 State St

Van's Systems

781 W Walcott Rd lot

W H Sutton Mechanical

202 W Cherry Dr


12637 S 265 W Suite 100


1510 S 19TH ST


3318 Pagosa Ct
Clinton Zip Codes

Join Angie's List to get the best local reviews in Clinton.

What Does My Membership Include?
  • Instant access to reviews for 700+ services
  • Exclusive service discounts - up to 70 percent off!
  • Top-notch support from our live call center
How does Angie's List work?
1. Say you need a Heating Repair
2. Angie's List has tons of detailed, local reviews.
3. Find a winner, and book them.
4. Angie's List is there to resolve any issues.
Good Morning America
Fox News
USA Today
The Wall Street Journal
MSN money